How to reset pentair easy touch panel.
At the outdoor control 1.press menu 2.press down button, scroll to settings. 3.Press right button to select. 4.Press up button, scroll to "Wireless Address" 5.Press right button to select. "Address Wireless scanning" will display, Then "Sending Address" will display. 6.Now repeat steps 1-5 with the handheld wireless controller, "Address Found ...
Push-button controls and intuitive displays take the guesswork and frustration out of setting up and modifying control programs. The EasyTouch PL4 control system is a four-circuit system designed for a single body of water, while the EasyTouch PSL4 system is a four-circuit system designed to control a pool/spa combination.Step 3: Restart the pump. Locate the reset button on the control panel of your Pentair pool pump. Press and hold the reset button for a few seconds until the lights on the control panel turn off. Release the button and wait for a few seconds until the lights turn back on. Turn on the power to the pool equipment and test the pump to see if it ... Remote Access Connection Instructions. From the Home screen, tap Settings > Advanced System Configuration > Network and WiFi Setup. and wait for your home network to be displayed. This can take up to a minute or more to complete. Select your home network and enter the password. Internet Connection Test to verify the Internet connection.
Press the Pool (P) button to activate the filter pump, rotate the pool/spa valve actuators and circulate the pool water and switch on the heater (if enabled in the Heat menu). Press the button again to switch the filter pump off. While the valves are rotating into position the filter pump will switch off.
The High Power Wireless Link consists of an indoor and outdoor 902-928 MHz wireless transceiver. Note: The wireless transceivers ship from the factory as a matched pair. The ID numbers on each transceiver must be the same number to function correctly. If needed, the transceivers must be replaced as a matched pair.
Attention User: This guide contains important information that helps ensure proper and safe operation and maintenance of this equipment. Retain this guide for future reference. Call (800) 831-7133 for additional free copies of these instructions or product labels. Refer to www.pentair.com for more information. Step 3: Restart the pump. Locate the reset button on the control panel of your Pentair pool pump. Press and hold the reset button for a few seconds until the lights on the control panel turn off. Release the button and wait for a few seconds until the lights turn back on. Turn on the power to the pool equipment and test the pump to see if it ...If you have any questions please contact us through our website at: https://www.poolspecialists.com/The MasterTemp has a max setting of 104. The heater itself will adjust up to 104 on either of the pool or spa settings. You need to see the actual temp on the heater. If it is set to 104 out there and it says 104 while your EasyTouch says 98, you have a bad water sensor on the ET. Keep in mind, you have two sensors.
Place the EasyTouch control panel face down on a flat clean surface. Remove the six screws securing the battery cover. Set the cover aside. crew (6x) Battery cover Easy Touch Control Panel (rear view) EasyTouch Wireless Control Panel Installation and User’s Guide... Page 16 OVER TIGHTENING THE SCREWS CAN DAMAGE THE UNIT.
Presidential Pools Pool School session from March 28, 2020. Service Manager, Jason Eakins, reviews the programming and operation of the Pentair EasyTouch Po...
The QuickTouch II wireless remote has an operating range of up to 250 ft. (line-of-sight) from the receiver. The receiver kit includes a 15 ft. connection cable. If needed, using extra cable, the cable length can be lengthened to 300 ft. The recommended locations for the receiver are shown below.Right button: Select LOW, MED or HI for the backlight brightness setting. Press the Back button to save the settings and to return to the previous screen. Settings Menu: Power Save. This option sets the time that the EasyTouch wireless control panel will shut down if there is no control panel activity.%PDF-1.6 %âãÏÓ 1102 0 obj > endobj 1123 0 obj >/Filter/FlateDecode/ID[78171EF34FD5B46928D582E8843AA9F3>]/Index[1102 35]/Info 1101 0 R/Length 112/Prev 6319449/Root ...Place the EasyTouch control panel face down on a flat clean surface. Remove the six screws securing the battery cover. Set the cover aside. crew (6x) Battery cover Easy Touch Control Panel (rear view) EasyTouch Wireless Control Panel Installation and User's Guide... Page 16 OVER TIGHTENING THE SCREWS CAN DAMAGE THE UNIT.About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy & Safety How YouTube works Test new features NFL Sunday Ticket Press Copyright ...Control From Across the Deck or Around the Globe. The ScreenLogic2 Interface allows you to control the key functions of a pool or spa using the IntelliTouch® and EasyTouch® control systems. You can remotely manage, monitor and control via mobile device. Easily change, track and monitor history of pH and ORP levels when using the IntelliChem ...
7" Profile 700 In-Wall Touch Screen Update (2011 and prior) Please ensure that the protocol adapter is up to date before proceeding with these steps. To update the In-Wall Touch Screen you must update three files stored on the device. The recommended method described here requires an active Ethernet connection to the Internet.%PDF-1.6 %âãÏÓ 1102 0 obj > endobj 1123 0 obj >/Filter/FlateDecode/ID[78171EF34FD5B46928D582E8843AA9F3>]/Index[1102 35]/Info 1101 0 R/Length 112/Prev 6319449/Root ...May 28, 2020 ... Pentair EasyTouch control panel series. I go over how to change your chlorine output of the salt cell on the panel. What would you like to ...The EasyTouch and IntelliTouch Control System Load Center and Power Center system transformer can be wired for 120 VAC at 2AMP 50/60 Hz (factory installed) or 240 VAC at 1AMP 50/60 Hz. The system transformer is pre-wired at the factory for 120 VAC service. To rewire the system transformer and for 240 VAC: Step 2. Use a small tipped object (such as an unfolded paper clip) to move the switches of the receiver. The receiver board has two sections of switches: "S1" and "S2." The "S1" switches control the communication link with the remote. The "S2" switch area controls the automatic countdown cycle for the shutdown of the spa jets. If you have questions about ordering Pentair replacement parts, and pool products, please contact: CUSTOMER SERVICE / TECHNICAL SUPPORT Customer Service and Technical Support, USA (8 A.M. to 4:30 P.M. — Eastern/Pacific Times) Phone: (800) 831-7133 www.pentair.com Important Safety Instructions .....Now, you can make it even more convenient to run your pool, spa or combination with the added ease of a wired or wireless remote. Plus, you can program your equipment for optimal energy efficiency. Allows easy upgrade to EasyTouch® Automation functionality for the following Compool® Systems: CP3400, CP3600, CP3800, CP3810, CP1000*, CP2000 ...
To change Compool EasyTouch circuit board: 1. Write down your Compool system settings and connections (e.g. filter pump schedules, auxiliary connection for lights, spa jets etc.). 2. Change system to SINGLE BODY system (jumper OFF): Remove circuit board Jumper J25. Place the jumper on one of the pins.Press the desired speed button (1- 4) to select the preset pump speed. When the selected speed button is pressed, the LED is on. The pump preset buttons and speeds are: Speed button #1, (750 RPM), #2, (1500 RPM), #3, (2350 RPM) and #4, (3110 RPM). Press the Start button. The pump will ramp to the selected preset speed.
Learn how to adjust the temperature in your pool or spa using the Pentair IntelliTouch control panel and ScreenLogic mobile app.Jun 25, 2018 · About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy & Safety How YouTube works Test new features NFL Sunday Ticket Press Copyright ... All it says is that it "ReInitializes the outdoor panel". It appears that it re-establishes communication with the panel. You may want to call Pentair and see if they'll …Locate the reset button on the Easy Touch panel, which is located in the top right corner of the display screen. 2. Press and hold down the reset button for five …To reset the pentair mastertemp 400, follow these steps: Turn off the power to the heater. Locate the reset button, usually on the control board or near the display. Press and hold the reset button for about five seconds. Turn the power back on, and the heater should reset.Whether you want to touch up some chips in your car’s paint or refinish a body panel after a fender bender, it’s important to find the original paint code if you want the color of ...Hello, You can access the salt level reading on your EasyTouch by pressing the Menu button, and using the Up and Down Arrows to select Diagnostics, then ...
You need to call the factory at 800-831-7133 and they can assist you. You may have to lower the control panel or what is called the Bezel to look at the Salt ...
Step 4: Thread the pressure gauge into the air relief valve in a clockwise direction. Use an open-end wrench to tighten the last half-turn. Do not over tighten. Step 5: Turn on the power to the pump at the breaker box. Close the air relief valve when a continuous stream of water flows out.
LINKS TO PURCHASE:IntelliCenter System (Load Center with i5P Personality Kit) (523448): https://www.epoolsupply.com/products/pentair-intellicenter-system-i5p...Features and Pros of EasyTouch system: The EasyTouch is the latest level of pool automation. You may use the EasyTouch 4 pool control system to automate all of your spa and pool's everyday activities. The EasyTouch outside control panel positioned at the pool equipment pad may manually regulate pool and spa service operations.Color Sync Controller Pentair Home app User's Guide... Page 17: Device Settings Control Panel Brightness: Adjust the brightness of the controller LEDs. Select Low or High' Tap Save to save the setting and return to the Lights page. • Remove Equipment: Remove the device from the Pentair Home app. Color Sync Controller Pentair Home app User's ...In this short video I will show you how to set the clock on Pentair's Easy Touch Automation. This is the first step needed when setting up either swimming po...Pentair system. Breaker won't reset due to drive going bad on u s pump? - Answered by a verified Pool and Spa Expert ... I have a pentair easy touch system and when I turn to Spa mode the pump is not coming on. It works fine in pool mode and the valves turn when spa mode is on but the pump doesn't come on. ... Pentair easy touch 4 panel is on ...Last-minute salt runs - and living with hard water - are now a thing of the past with the Connected Salt Level Sensor. Installation is easy with the universal brine tank clip, and setup is simple with step-by-step instructions in the Pentair Home app. But, if you hit a snag, we're here for you. Anytime. Anywhere.If you have any questions please contact us through our website at: https://www.poolspecialists.com/From our residential and commercial water solutions, to industrial water management and everything in between, Pentair is focused on smart, sustainable water solutions that help our planet and people thrive. Our MissionControl From Across the Deck or Around the Globe. The ScreenLogic2 Interface allows you to control the key functions of a pool or spa using the IntelliTouch® and EasyTouch® control systems. You can remotely manage, monitor and control via mobile device. Easily change, track and monitor history of pH and ORP levels when using the IntelliChem ...To connect the receiver cable to EasyTouch or IntelliTouch load center: 1. 2. Unlatch the load center front door spring latch, and open the front door. 3. Remove the two screws securing the high voltage cover-panel, and remove it from the enclosure (illustration below shows cover-panel removed). 4.EasyTouch Indoor Control Panel for 4 Circuit Systems. Rquires running wire from the outdoor power center back to the indoor wall mounted contoller. ... For more information, please see the Pentair Easy Touch User's Guide. Reply ? Asked on 1/15/2017by Dave. The description says for a four function system, but the picture shows 8 buttons. Which ...
Control panel Circuit board Raceway Insert the four wires into the screw terminals of the COM PORT plug located on the circuit board as shown on page 6. Using a small flat-blade screwdriver, secure the wires with the screws. Page 10 10. Switch the power on to the IntelliTouch or EasyTouch Control ® ® System Load Center. 11.From https://www.justanswer.com/ythiJustAnswer Customer from San Antonio, TX: I'm getting an error code 4 on my Pentair easy touchPearl Wilson: Assistant: Ho...The quality you expect from Pentair products, backed by our warranty. Learn more about warranties available for Pentair products. Select Your Product Category. Pool Products. Warranty Information Product Registration. Water Softening & Filtration Products. Warranty Information.Instagram:https://instagram. 1004 winnsboro rdidaho transportation road reportmaine moose hunting success ratesvan buren county police scanner Pentair control panel, pentair mini max heater. Just purchased the house. Heater seems to show working when in auto mode. No acces to iaqualink link app. When I switch to service mode to heat the spa, … read more lewis fresh market weekly adpopeyes louisiana kitchen grand haven menu Remote Access Connection Instructions. From the Home screen, tap Settings > Advanced System Configuration > Network and WiFi Setup. and wait for your home network to be displayed. This can take up to a minute or more to complete. Select your home network and enter the password. Internet Connection Test to verify the Internet connection. downey promenade dental group Press the Pool (P) button to activate the filter pump, rotate the pool/spa valve actuators and circulate the pool water and switch on the heater (if enabled in the Heat menu). Press the button again to switch the filter pump off. While the valves are rotating into position the filter pump will switch off.Step 4: Thread the pressure gauge into the air relief valve in a clockwise direction. Use an open-end wrench to tighten the last half-turn. Do not over tighten. Step 5: Turn on the power to the pump at the breaker box. Close the air relief valve when a continuous stream of water flows out.